Thingmagic Mercury xPRESS Platform v1.7 Manual de usuario Pagina 130
- Pagina / 144
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Preparing the xPRESS motherboard
A DIVISION OF TRIMBLE
130
Preparing the xPRESS motherboard
We recommend that you erase the memory on the xPRESS motherboard before running
a new application. This is especially important when running SAM-BA because the default
application on the xPRESS motherboard is designed to reconfigure the USB “OTG” port
to simulate a keyboard and the SAM-BA will not communicate with this interface when it
is in this mode. The steps to follow erase memory are as follows.
1. Power down the xPRESS motherboard. The red “Power” LED must be off. Depending
on the position of the “Always-on” jumper, you may have to disconnect all sources of
power, including the AC Adapter, USB cables, and rechargeable Li-ion battery.
2. If you have installed a coin cell battery in the round socket (shown below), you should
remove it.
3. Move the memory jumper to the erase position.
4. Apply power to the xPRESS motherboard (ideally using AC Adapter). Use the “ON/
OFF” switch to turn the board on (or move the power jumper into the always-on
position) for 10 seconds.
- Mer cury 1
- SDK Version 1.7.1 1
- Revision Table 3
- Contents 5
- 6 Contents 6
- 8 Contents 8
- Introduction 9
- Ordering Information 10
- M6e: QV5MERCURY6E 12
- Bluetooth Module: T9J-RN42 12
- WiFi Module: T9JRN171-1 12
- Quick Start Guide 17
- Hardware 18
- Software 19
- Hardware Setup 21
- 22 Quick Start Guide 22
- Quick Start Guide 23 23
- 24 Quick Start Guide 24
- Using the Sample Application 25
- RFID Sensor Application 26
- Demo App Program Flow 27
- RTC: Real Time Clock 28
- Connecting to the Console 30
- Console Commands 30
- Log and Debug Levels 33
- Using the Optional Modules 35
- Bluetooth Module 36
- Using the Optional Modules 37 37
- 38 Using the Optional Modules 38
- 7. Select Pair 39
- Using the Optional Modules 41 41
- RFID Sensor Demo Instructions 43
- RN-42 Initialization 44
- RN-42 Flow Control 45
- RN-42 Connection Status 45
- WiFi Module 46
- Using the Optional Modules 47 47
- #define ENABLE_OUTPUT_BT” 47
- Features Implemented 48
- Using the Optional Modules 49 49
- Initialization Process 50
- Using the Optional Modules 51 51
- Connection Status 52
- Power Management 52
- Console Command Control 53
- Configuration Settings 54
- Joining Networks 57
- 58 Using the Optional Modules 58
- Known Limitations 59
- Power-Over-Ethernet Module 60
- Using the Optional Modules 61 61
- Power over Ethernet 62
- Configuration 62
- GPS Module 66
- GPS Metadata 67
- 68 Using the Optional Modules 68
- is 2 output fields, not 1 68
- Using the Optional Modules 69 69
- Windows OS 71
- Install Java 72
- Click Extract 75
- Install USB Driver 76
- Next Steps 76
- Installing Java Runtime 79
- • Open a terminal shell 80
- Project Building 87
- Common Build Errors 88
- Common Error 2 89
- Obtaining a JTAG ICE 89
- JTAG Hardware Installation 90
- Accept config defaults 95
- Running the Debugger 97
- Using the Developer Toolkit 100
- A DIVISION OF TRIMBLE 101
- Disconnecting the Console 103
- Hardware Reference Guide 105
- Processor (MCU) 106
- RFID Module 107
- Battery Charging Controller 108
- AC Adapter Input 109
- Hardware Reference Guide 111 111
- OTG USB Interface 112
- Hardware Reference Guide 113 113
- Debug USB Port 114
- Module USB Interface 114
- Programmable LEDs and Switch 115
- “Coin” battery 115
- 116 Hardware Reference Guide 116
- Hardware Reference Guide 117 117
- Test Interface 118
- Power Source Precedence 119
- AC Input Adapter 120
- USB Connection 121
- Li-ion Battery 122
- Comm Bus (“POE”) Power 122
- Known HW Limitations 123
- Known Issues 123
- 124 Hardware Reference Guide 124
- Software Reference Guide 125
- Toolchain 126
- Toolchain Downloads 126
- Toolchain Build Instructions 127
- JLink GDB 127
- 128 Software Reference Guide 128
- Installing SAM-BA Software 132
- Using SAM-BA 140
Relacionado con productos y manuales para Hardware Thingmagic Mercury xPRESS Platform v1.7
Hardware Thingmagic M6e Manual de usuario
(100 paginas)
(100 paginas)
Hardware Thingmagic Micro Hardware Manual de usuario
(105 paginas)
(105 paginas)
Hardware Thingmagic M5e-Compact Manual de usuario
(252 paginas)
(252 paginas)
Hardware Thingmagic Astra-EX Manual de usuario
(90 paginas)
(90 paginas)
Hardware Thingmagic Vega Manual de usuario
(20 paginas)
(20 paginas)
Hardware Thingmagic Astra Manual de usuario
(75 paginas)
(75 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales